NEWS CENTER / 新聞資訊
當前位置:網站首頁 > 新聞資訊 > 行業資訊
ALL NEWS / 行業資訊
- V-Cut設計及使用上有哪些限制?
- 本站編輯:杭州博野精密工具有限公司發布日期:2018-06-01 13:23 瀏覽次數:
V-Cut雖然可以方便我們輕易的將板子分開并去掉板邊,但V-Cut也是有設計及使用上的一些限制。
Although V-Cut can facilitate us to easily separate the boards and remove the edges, V-Cut also has some limitations in design and use.
,V-Cut只能切直線,而且一刀到底,也就是說V-Cut只能切割成一條線直直的從頭切到尾,它無法轉彎改變方向,也不能像裁縫線一樣切一小段后跳掉一小段。這是因?yàn)閂-Cut的凹槽是使用上下兩片圓盤的電鋸所切出來的,有看過木工師傅裁切木頭吧,意思大概就是那樣,因?yàn)镻CB的裁切都要很精淮(毫米計算),所以無法做到只切一半就退刀的作業,其實也不是做不到,而是沒有必要大費周章這么做,我們只要放棄V-Cut分板的制程,改用Routing去板機來裁切板子就可以達成了。所以一般如果是比較複雜的切斷路徑,就會改用Routing機來分板。
First, V-Cut can only cut a straight line, and a knife to the end, that is, V-Cut can only cut into a straight line from the head to the tail, it can not turn to change direction, and can not cut a small segment like a tailor line and jump a short section. This is because the grooves of the V-Cut are cut out by the saws that use two discs up and down, and have seen the woodworker cut the wood, which is probably the same, because the cutting of the PCB must be very fine (millimeter calculation), so it is impossible to cut the knife only half and not do it, but it is not necessary, but not necessary. If we do so, we just need to give up the process of V-Cut sub board and switch to the Routing board to cut the board. So in general, if it is a complex cut off path, it will be replaced by Routing.
其次,PCB在行經回焊爐的高溫時,板子本身就會因?yàn)楦邷爻^玻璃轉移溫度(Tg)而軟化變形,如果V-Cut位置及凹槽深度設計得不好,會使得PCB變形更會嚴重,不利二次回焊制程。
Secondly, the PCB will soften the deformation because of the high temperature exceeding the glass transfer temperature (Tg). If the V-Cut position and the depth of the groove are not well designed, the PCB deformation will be more serious and the two return welding process is disadvantageous to.
另外,PCB厚度太薄也不適合做V-Cut凹槽,一般如果厚度在1.0mm以下的板子,深圳宏力捷就不建議做V-Cut了,這是因?yàn)閂-Cut凹槽會破壞原本PCB的結構強度,當有設計V-Cut的板子上面放置有比較重的零件時,會因?yàn)橹亓Φ年P(guān)系而使得板子變得容易彎曲,這非常不利SMT的焊接作業(容易造成空焊或短路)。
In addition, the thickness of PCB is too thin to be suitable for V-Cut grooves. Generally, if the thickness is below 1.0mm, Shenzhen macroczech will not recommend V-Cut. This is because the V-Cut groove will destroy the original structural strength of the original PCB. When there is a relatively heavy zero part on the board of the designed V-Cut, it will make the plate because of the relation of gravity. The child becomes easy to bend, which is very unfavorable to the welding operation of SMT (which is likely to cause air welding or short circuit).